Free 3D model

Marble Lift Tower

A marble run in two parts. Turn the knob and the screw in the middle carries the marbles up the inside of the tower, one on every turn. At the top they roll out through a window onto a spiral track, run down round the tower and come back to the screw by themselves, so it never stops as long as you keep turning. The tower with its track is one print and the screw with its knob the other. No screws, no glue, no supports. It runs on 16 mm glass marbles; a printed ball is in the ZIP if you have none.

  • 8printed parts
  • 10 × 10 × 15 cmassembled (L × W × H)
  • ≈ 0.2 kgfilament in total
  • 100 × 100 mmbed size needed for the tower, 122 mm tall; the screw is 149 mm tall
Download all files ZIP · 0.5 MB

Free for personal use under CC BY-NC 4.0: print it, remix it and share it with credit to Shapekit. Please don't sell the files or the prints.

Take it apart in 3D · Parts · How to build it

In 3D

Turn it, take it apart

Every part as you print it. Pick colours to see what your filament will look like.

The 3D model (1.3 MB) loads when you get here.

Preview colours

Tower and track
Screw
Marbles

Drag to rotate · scroll or pinch to zoom

In the download

3 parts, ready to print

Every STL is already placed the right way up. Download them all at once, or one by one.

Tower

The tower, its foot and the spiral track in one piece, 100 mm across and 122 mm tall. Inside are the bore for the screw and the groove the marbles climb in; the window at the top and the channel at the foot connect the groove to the track.

Size
122 × 100 × 100 mm
Print
Upright. No supports: the track stands on a 45° bracket, the window and the channel have a pointed roof.
Filament
≈ 188 g
STL 0.7 MB: Tower

Screw

A Ø30 mm flight with a 24 mm pitch on a Ø14 mm core, with the knob and its peg on top. A hole in its foot turns on a pin in the floor of the tower.

Size
149 × 44 × 44 mm
Print
Standing on its bottom end, with a brim. No supports: the underside of the flight and of the knob is 45°. It is 149 mm tall, so print it slowly.
Filament
≈ 28 g
STL 0.6 MB: Screw

Marble × 6

A 16 mm ball with a small flat to print on, for when you have no glass marbles. Print up to six.

Size
16 × 16 × 16 mm
Print
On its flat, with a brim. Sand the seam and the flat.
Filament
≈ 8 g
STL 0.1 MB: Marble
Also needed

Parts you buy

  • Nothing for the tower itself: no screws, no glue, no bearings.
  • Up to 6 marbles of 16 mm, the standard size. Glass marbles run best; the printed ball in the ZIP also works.
Print settings

Slicer settings

0.20 mmlayer height
3walls
15%infill
PLA or PETGmaterial

For a 0.4 mm nozzle. Filament amounts are estimates for these settings.

Assembly

How to build it

Print the tower

Upright, no supports. It is the long print of the two. Check that the track, the window at the top and the channel at the foot are free of strings.

Print the screw

Standing on its bottom end with a brim, slowly. Break the brim off and clean the pin and the thin start of the flight at the bottom: that edge has to slide under the marbles.

Put it together

Lower the screw into the tower until it drops onto the pin in the floor. It should spin freely.

Run it

Lay one marble on the track and turn the knob clockwise, seen from above. The marble rolls into the tower, climbs, comes out at the top and runs down. Add marbles one at a time, up to six.

Marbles are a choking hazard: keep them away from young children.

Good to know

How does the screw lift the marbles?

A marble sits half in an upright groove in the wall of the tower and half on the flight of the screw. The groove keeps it from going round with the screw, so the turning flight can only push it up, 24 mm on every turn.

Do I need glass marbles?

They run best: 16 mm, the standard size. If you have none, print the ball from the ZIP and sand it smooth. Steel balls of 16 mm work too.

Does it need supports?

No. The track rests on a 45° bracket, the flight of the screw has a 45° underside, and the two openings in the tower have a pointed roof.

How big is it and how much filament does it take?

100 mm across and 153 mm tall with the knob. The tower fits any printer with a 100 mm bed; the screw needs 149 mm of height. Together they take about 220 g.

Which way do I turn it?

Clockwise, seen from above. Turning the other way pushes the marbles down instead of up; nothing breaks, they just stay at the bottom.

A marble stays at the bottom and is not picked up. What now?

Look at the bottom end of the screw: the flight starts as a thin wedge that has to be clean and sharp. Cut away what is left of the brim and any blob there. A printed ball must lie with its flat away from the floor.